Altera usb blaster linux how to#
Altera usb blaster linux install#
Altera usb blaster linux drivers#
Altera usb blaster linux update#
Altera usb blaster linux driver#

Seems better but 1V amplitude still bothers me.

Doesn't look healthy at all (note the time scale). I checked with an oscilloscope what the signals look like when i try to run 'detect' command. I also know that UsbBlaster is working fine at least with Altera FPGA (and i have two of them UsbBlasters, they behave the same). Warning: UrJTAG may damage your hardware! There is absolutely no warranty for UrJTAG. Welcome to change it and/or distribute copies of it under certain conditions. UrJTAG is free software, covered by the GNU General Public License, and you are Here's the output i get when i try to detect JTAG devices in bfin-jtagД¬opyright (C) 2007, 2008, 2009 Kolja Waschk and the respective authors So don't trust updating OpenSuse.EMU and TRST signals are left unused as EMU can be ignored and TRST seems to be able to be not used and replaced by special sequence via TMS. But I hadn't added much and I kept my own stuff under /home which is setup as a separate file system to I can reinstall without wiping /home. After that rebooted and system had lots of problems. I followed OpenSuse instructions carefully.

Altera usb blaster linux update#

Is that the xserver name? Anyway it works fine with that.Д«y the way first I tried to update OpenSuse from 11.2 to 11.4 which was supposed to work. I added 'nomodeset' which causes it to use nv instead of nouveau. Solution for that was at GRUB boot menu there is a spot below where boot options can be added. These chips require a JTAG programmer to configure. For a project I am working on I wish to make use of an Altera EPM7032S chip. The aim of this project was to use a Raspberry Pi Zero (or Zero W) as a replacement for the Altera 'USB Blaster' chip programmer.

Altera usb blaster linux driver#

OpenSuse 11.4 video driver was messing up the screen with lots of garbage. Raspberry Pi Altera 'USB Blaster' Gadget - FAILED.

Altera usb blaster linux install#

Probably good to install it on a separate partition or USB drive if you sysem is already all setup and loaded with stuff you don't want to re-setup. So if you're using an older openSuse try installing 11.4. It won't let me ps -9 (die sucker) it until I exit quartus. It's good to do > ps -ef | grep jtag to see the jtagd demon get created and it's parameters and see if it is deleted when quartus exits. Then I created the ~root/.nf (empty file). USB Blaster didn't work until I first ran quartus as root. Ohhh I just ran it again (editing this post). I didn't change anything!!!!! except telling the programmer to use the USB-Blaster. After that reinstalled Quartus 11.0sp1 and told the programmer to use the USB-Blaster and clicked and WOW!!!! It worked!!!!! I did nothing to this new OpenSuse 11.4 installation. I have USB blaster plugged into a Cyclone II evaluation board.ДЄnyway because I wanted to have the latest version of wine I decided to update OpenSuse to 11.4. Spent several hours for a few days I think carefully trying everything posted here. Followed the instructions of all the Altera documents and added all the USB stuff under the /etc directory. On AMD 64-bit OpenSuse 11.2 on a HP Pavillion laptop about 3 years old I had lots of problems getting USB Blaster to work. Run a jtagconfig to confirm a happy installation Now you will also need to and your users to a group with permissions to use the USB ports, or do a chmod -R 557 of /proc/bus/usb This sets up your USB-Blaster permissions so that any user can access it.ДЄlso do a 'chmod +x /etc/hotplug/usb/usbblaster' to make the script executable. Then add the following script as /etc/hotplug/usb/usbblaster USB-Blaster configuration This part is based on a blog post from fpga-dev. Please note that this tutorial is intended for Debian-derived Linux distros such as Ubuntu, Mint, MX, etc. Usbblaster 0x03 0x09fb 0ењ†002 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 Installing and Running Alteras Quartus II on Linux. (I found some instructions in a NIOS II release)ДЇirstly you need to set up the permissions by adding and entry to the /etc/hotplug/usb.usermap. I have only done this on RHE3 and 4, but it's a similar story for SUSE etc. Additional the USB Programmer2 has the following features: - USB: Micro-USB Connector, USB 2.0 HS support - Voltage levels supported: 0.8 to 3. By default, root is the only user allowed to use usbfs.

Altera usb blaster linux drivers#

The Quartus II software uses the built-in USB drivers (usbfs) on RedHat Linux to access the USB-Blaster download cable.

Altera usb blaster linux how to#

It is possible to install the USB Blaster for Linux, but you will need to change some permissions to allow users access to the USB ports (and their are some differences between distro's). USB Programmer2 (Trenz/Arrow): 30 (35-40), 21MBit speed. Installing the USB-Blaster Driver on Linux This section describes how to install the USB-Blaster driver on Linux.